国产99热精品_欧美疯狂做受xxxx猛交_婷婷在线网站_日韩无遮挡毛片_欧美高清momspuss_欧美激情福利

FLDA3516S_FLDA3517ST_FLDA3518S_FLDA3519G_FLDA3520C轉子流量計OMEGA

直讀式空氣、水、N2、H2、 CO2、Ar、He和O2轉子流量計

計量管帶有導流條或?qū)Я鞑郏兄谔峁┛煽俊蚀_的讀數

正面防護罩中的放大透鏡可增強讀數分辨率

流量管與浮子具備互換性

流量管的安裝與更換非常方便

簡便的面板安裝方式

FLDA3516S_FLDA3517ST_FLDA3518S_FLDA3519G_FLDA3520C轉子流量計OMEGA

標準精度：滿量程的±5%

重復性：±0.25%

可用流量范圍：最小為10:1

最大工作壓力：200 psig/13.8 bars

最高工作溫度：121°C (250°F)

材質

流量管：厚壁硼硅酸鹽玻璃

浮子：玻璃、紅藍寶石、316不銹鋼、鎢鈷硬質合金和鉭與液體接觸的安裝接頭的選擇：黑色陽極氧化鋁或316不銹鋼

側面板：黑色陽極氧化鋁

正面防護罩：帶有縱向放大透鏡的聚碳酸酯樹脂，可增強讀數分辨率

背板：1?8”厚白色丙烯酸樹脂

O形圈和填料：鋁質／銅質流量計中采用丁鈉橡膠O形圈。不銹鋼流量計中采用氟橡膠O形圈

選配：全氟橡膠和EPR

連接口：1?8 NPT內螺紋入口和出口連接口

FLDA3516S_FLDA3517ST_FLDA3518S_FLDA3519G_FLDA3520C轉子流量計OMEGA

Direct Reading Rotor Flowmeters for Air, Water, N2, H2, CO2, Ar, He and O2

Metering tube with guide strip or guide groove is helpful to provide reliable and accurate reading.

Amplifying lens in front shield can enhance reading resolution

Flow pipes and floats are interchangeable

Installation and replacement of flow tube is very convenient.

Simple installation method of panel

FLD series rotor flowmeter is a kind of precision instrument, which is specially used to read the flow directly. They embody the simple, universal and economical characteristics inherent in the classical rotor flowmeter. It is very suitable for measuring carrier gas, indicating and controlling the gas in the process of processing in the chromatographic separation method. It is also very suitable for gas measurement in laboratories and experimental factories, as well as flow and liquid level indication. When fully assembled and shipped, these flowmeters include standard fittings (available in a variety of materials), side panels, thicker front enlargement shields and back panels, as well as built-in control valves and flow pipes. Using the selected acrylic triangle frame FLTR-1, the panel mounting mode can be transformed into the bracket mounting mode. The trigonometer is equipped with a level gauge and a leveling screw.

Flowmeters are equipped with built-in 6-ring needle valves, 16-ring high-precision metering valves with "non-ascending stem", or may not be equipped with any valves. As long as high sensitivity control and high resolution are required, especially when used in conjunction with metering tubes for measuring very low flow rate, high-cost high-resolution valves are worth the money. Generally speaking, when measuring gas, it is recommended to install the valve at the entrance (bottom); when measuring liquid, the valve can be installed at both the entrance and the exit (top). For vacuum applications, valves must be installed at the outlet. If not specified at the time of ordering, the valve will be installed at the inlet of the flowmeter at the time of shipment.